







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterStanding Seam Metal Roof in Burbank, CA
A standing seam metal roof in Burbank typically costs between $18,500 and $42,000 for most single-family homes, and the panels are expected to last 40 to 70 years. Standing seam means the vertical seams between panels are raised and fastened with concealed clips, so there are no exposed screws on the roof surface and the panels float as the metal expands and contracts in the heat. For Burbank homeowners facing a re-roof after a long stretch of sun and Santa Ana wind, it’s the longest-horizon choice on the market right now.
We install standing seam through our Roofing division, and we do it on houses across the Burbank flats, the hills above Glenoaks, and the older blocks near downtown where the original roofs were built for a cooler, wetter climate than the one they actually get. Burbank runs hot. Summer attic temperatures climb fast under anything less than a properly ventilated metal roof, and the sun here breaks down asphalt shingles years earlier than the manufacturers’ national estimates suggest. Metal sidesteps that whole problem.
If you’re weighing metal against shingle or tile, call us at (844) 797-7958 and we’ll walk through the numbers honestly, including the cases where metal isn’t the right call. Call any hour, any day. A live person answers, not a voicemail.
Key Takeaways
- Standing seam metal roofs run $18,500 to $42,000 in Burbank depending on square footage, roof pitch, and panel type.
- Concealed fasteners mean no exposed screws, so the roof surface stays watertight and clean-looking for decades.
- Metal handles Burbank’s heat and wind better than asphalt shingles, which crack and lose granules under sustained UV.
- Every installation is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right.
- Upfront pricing means the number you see is the number you pay, with 0% financing for 18 months available.

When You Need Standing Seam Metal Roof
Metal isn’t the answer for every Burbank house, and we’ll tell you when it isn’t. But these are the situations where a standing seam roof earns its cost back:
- Your asphalt shingles are failing after 12 to 15 years. Burbank’s UV load is brutal on shingle roofs. Granule loss, curling edges, and toasty attic air show up years before the 25-year rating suggests. If you’ve already patched twice and you’re seeing balding shingles on the south-facing slope, metal ends the cycle instead of restarting it.
- The Santa Ana winds have been peeling shingles off. If your roof is on the north side of the Verdugo foothills or any exposed ridge, wind lift on shingles is real. Standing seam panels are fastened with clips and interlocked at the seams, which is why they hold up to sustained gusts much better than nailed-down shingles.
- You’re in an older Burbank bungalow and the roof is original. On homes near Magnolia Park and the streets off Olive, we regularly find roofs that were built with whatever was available in the 1950s and have been patched piecemeal since. A proper tear-off and standing seam install gives the house a fresh start above the deck, and lets us inspect the sheathing while we’re up there.
- You want a roof you won’t be re-doing in your lifetime. A properly installed standing seam roof realistically lasts 40 to 70 years. If this is the last roof your house is going to need, it’s worth choosing once and choosing right.
- You’re adding solar and want clean mounting. Standing seam roof panels hold solar mounting clamps without drilling through the surface, which is a real advantage if you’re leaning toward panels in the next few years. Non-penetrating solar clamps are much less likely to leak than lag bolts through shingles.
- You like the low-maintenance promise of a metal roof but want to avoid exposed fasteners. Screw-down metal panels have rubber washers that eventually dry out and back out in Burbank heat. Standing seam hides every fastener under the seams, so there’s nothing on the surface to loosen or leak.
If any of that describes your house, the honest first step is a free roof inspection. We’ll look at the existing roof, check the decking, and tell you whether metal is the smart move or whether a well-installed shingle roof buys you 20 more years for less money. That’s part of how we look after homes in the Burbank service area.
Our Standing Seam Metal Roof Process
Standing seam is unforgiving of shortcuts. The panels are long, the seams have to be perfect, and the flashing at every transition has to shed water the first time. Here’s how a Groundwork install actually goes:
- Free inspection and measurements. We get on the roof, check the sheathing condition, look at the existing ventilation, and measure every plane. If the decking is compromised under the old roof, we’ll tell you before the estimate goes out, not after the crew starts tearing off.
- Upfront written estimate and material selection. You get a job-specific quote with line-item pricing, not a lump-sum number. We’ll walk through panel widths, color options, and material choices. Our vetted brand partners cover everything from panel profiles to trim, and we’ll tell you which specific products make sense for a Burbank install instead of letting a catalog pick for you.
- Tear-off and sheathing inspection. We remove the old material, inspect every square foot of decking, and replace anything that’s soft or compromised. On older Burbank homes, this is where a lot of unexpected rot gets found. You see what we see before we add anything to the bill.
- Underlayment and flashing first. The most common standing seam failure is water getting under the panels at a penetration or a valley. We install high-temperature synthetic underlayment across the whole deck, then detail the valleys, the wall flashings, the vents, and the chimney transition properly before any panel goes up.
- Panel installation with concealed clips. Panels are cut to length on-site, hoisted, and locked into concealed clips that allow the metal to expand and contract with temperature. That’s the single most important part of the process, and it’s why a metal roof done without expansion allowance buckles and oilcans within a couple of summers.
- Final walkthrough and cleanup. We walk the roof with you, show you the seams, the flashings, and the ventilation, and we pull a magnet across the yard to get the screws out of the grass. Every job we complete is backed by the 730-Day Done Right Promise, which is one of the longest workmanship guarantees in the residential construction space.
Our technicians bring up to 12 years of experience to roof jobs, and every one of them is background-checked and arrives in uniform. You won’t see an unmarked van pull up and a crew you’ve never met walk onto your roof. That isn’t a wedge for us. It’s just how we run the company. If a roof is in the plan alongside other work on the house, like replacing gutters, patching the fascia, or refreshing a whole façade with James Hardie siding at the same time, we can scope it all together rather than sequencing three different contractors.

Standing Seam Metal Roof Pricing in Burbank
Metal roofs are priced by the square (100 square feet of roof area), and a typical Burbank home lands somewhere between 22 and 40 squares. Here’s what honest Burbank pricing looks like. The numbers below are the ranges we see across the neighborhoods we work in; your actual estimate depends on the specifics of your roof.
| Item | Typical Burbank Range |
|---|---|
| Full standing seam install, single-story, 22-28 squares | $18,500 – $26,500 |
| Full standing seam install, two-story or complex roof, 30-40 squares | $28,000 – $42,000 |
| Standing seam price per square, installed | $750 – $1,150 |
| Tear-off of existing roof (per square) | $180 – $320 |
| Sheathing replacement (per sheet, if needed) | $65 – $120 |
| Flashing and penetration detail work | $400 – $1,800 (varies by complexity) |
| Solar mounting clamp installation (if adding solar) | $35 – $75 per clamp |
What drives the number up or down in Burbank specifically:
- Roof pitch and complexity. A simple hip roof on a single-story Bakersfield-style ranch is the low end. A cut-up roof on a hillside home above Glenoaks with dormers, valleys, and multiple planes pushes toward the top of the range. Every seam and every flashing detail takes time.
- Panel type and color. Signature colors and premium panels cost more than standard colors. Our brand partners cover a range of panel profiles, and we’ll steer you toward the ones that hold up cleanly in Burbank’s sun without color fading within a decade.
- Decking condition. Any home built before 1970 in Burbank should expect at least some sheathing replacement. Old roofing was often installed over spaced board decking rather than plywood, which means the deck may need to be topped with solid sheathing before metal goes on.
- Ventilation upgrades. Metal roofs trap heat just as much as any other roof if the attic isn’t vented properly. Ridge vents and proper intake ventilation are common add-ons, and they’re not optional in Burbank.
- Existing solar to remove and reinstall. If you already have panels, expect $2,000 to $4,000 to detach and reinstall.
We do free project estimates and design consultations, so you get the actual number for your roof before you commit. No-hassle upfront pricing means the number you see is the number you pay. On larger projects, we can apply $1,000 off any project over $10,000, and 0% financing for 18 months is available for qualified buyers. If you’re combining a metal roof with other exterior work, the financing makes it much less of a single-hit cost.
One more cost note worth saying out loud: a metal roof is more expensive than shingle up front, sometimes by $8,000 to $15,000. It’s also likely the last roof your house needs. When you spread the cost over 40 to 70 years instead of 15 to 20, the annual cost is often lower than shingle. We’ll show you that math on paper before you decide.
FAQs – Standing Seam Metal Roof
How much does a standing seam metal roof cost in Burbank?
Standing seam metal roofs in Burbank run $18,500 to $42,000 for most single-family homes, with the typical install landing around $22,000 to $30,000. The final number depends on your roof’s square footage, pitch, complexity, decking condition, and panel choice. We give you a written, line-item estimate for free, and the price doesn’t move unless something changes on the roof that you approve first. Call (844) 797-7958 for a free quote.
Is standing seam metal roofing worth the cost compared to shingles in Burbank?
For most Burbank homeowners planning to stay in the home long-term, yes. Standing seam lasts 40 to 70 years versus 15 to 20 for asphalt shingles in Burbank’s heat, it holds up better to Santa Ana winds, and it runs cooler in summer. If you’re moving in a few years, a quality shingle roof is often the smarter financial call, and we’ll tell you that. Call (844) 797-7958 to talk through which option makes sense for your house.
Can you install a standing seam metal roof over my existing roof in Burbank?
We don’t recommend it, and we won’t do it on most Burbank homes. Standing seam is installed with clips that need to be fastened into solid decking, and going over old shingles hides whatever condition the decking is really in. Tear-off lets us check the sheathing, which is where most of the rot in older Burbank homes hides. We’ll always quote the full tear-off, not the shortcut. Call (844) 797-7958 to schedule a free inspection.
How long does a standing seam metal roof installation take?
A typical Burbank standing seam install takes 5 to 10 working days from tear-off to final walkthrough, depending on roof size and complexity. Simple single-story roofs finish closer to 5 days; larger or more cut-up roofs near the upper end. We give you the timeline in writing with your estimate, and we tell you up front if weather could push it. Call (844) 797-7958 to get scheduled.
Is a metal roof noisy in the rain?
No, not on a properly built home. Standing seam metal installed over solid sheathing and underlayment sounds quieter than shingles in most homes because the mass between the panels and the attic absorbs the impact. The “noisy metal roof” concern is really about old barn roofs installed over open purlins, which isn’t how residential standing seam is built in Burbank. If you have questions about what to expect, call (844) 797-7958 and we’ll walk you through it.
Does a metal roof handle Burbank heat better than shingles?
Yes. Metal reflects more solar radiation than asphalt shingles, and Burbank’s summer UV is the single biggest reason shingle roofs fail early here. A ventilated standing seam roof can knock several degrees off attic temperatures compared to a comparable shingle roof, which takes load off your AC and helps the whole house run cooler. Call (844) 797-7958 for a free attic and roof inspection.
Ready to Talk Roofs?
Standing seam is a big decision and a serious investment. We treat it that way. You get a free inspection, an upfront written estimate, and a crew that shows up when we say, in uniform, ready to do the work. Every install is covered by the 730-Day Done Right Promise. If it’s not done right, we make it right.
Call Groundwork Construction Co. of Burbank at (844) 797-7958 for a free estimate. A live person answers around the clock, and we can typically get an inspector to your house within a few days.
Written by the team at Groundwork Construction Co. of Burbank, serving Burbank.


