







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Concrete Driveways & Concrete Work in Glendale, CA: What It Costs and How Long It Takes
Concrete driveways and concrete work in Glendale, CA typically run $4,500 to $12,000 for a full driveway install, and most residential pours are finished in 3 to 5 working days from demo to first drive-on. Replacement of an existing slab sits in the same band, usually $5,000 to $14,000 once haul-off and base repair are counted. The number that matters most is subgrade: a Verdugo foothills lot with slope and drainage problems costs more than a flat lot near downtown, and that difference shows up before the first yard of concrete arrives. Call (844) 797-7958 for a free on-site estimate.
How a Concrete Job Moves From Bare Dirt to a Finished Drive

Concrete work rewards patience and punishes shortcuts. Here’s the real sequence we run on a Glendale driveway, with the decisions you’ll be making along the way.
Stage 1: Demo and haul-off (day 1)
Old concrete comes out with a breaker and a skid steer, and the debris goes into a dumpster on site. On a typical two-car driveway, demo and haul-off take one day. You decide here whether the existing base stays or gets excavated to full depth. If the old slab cracked because the base was thin, we replace the base; leaving bad base under new concrete is how you pay twice.
Stage 2: Grading, drainage, and forms (days 1 – 2)
We cut the subgrade to grade, compact it in lifts, and set the slope so water runs to the street or a drain rather than toward the garage. Forms go up next, and you walk the layout before anything gets poured. This is your chance to widen a parking pad, adjust the apron, or add a walkway connection without a change order later. Drainage is where hillside Glendale properties need the most attention.
Stage 3: Base and reinforcement (day 2)
Class II base goes in at 4 to 6 inches, compacted, then rebar or welded wire mesh is tied and chaired so it sits mid-slab instead of on the ground. You choose the reinforcement spec at the estimate stage. For a standard residential drive, #3 rebar on 18-inch centers is common; heavier loads like an RV or a heavy truck push toward #4 bar and a thicker slab.
Stage 4: The pour and finish (day 3)
Concrete arrives by truck, gets placed, screeded, floated, and finished. You choose the finish: broom for grip, salt-and-pepper, exposed aggregate, or a light stamp. Control joints get cut within 12 to 24 hours to control where the concrete cracks. A typical residential driveway pour takes 4 to 8 hours on site.
Stage 5: Cure and drive-on (days 3 – 10)
Concrete cures for 7 days before you drive on it and 28 days before it reaches full design strength. We keep the site barricaded and return to strip forms, clean joints, and seal if you’ve chosen a sealer. You’ll get a walkthrough and a written record of the mix design, thickness, and reinforcement used.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between for Concrete Work in Glendale
- Standard broom finish: the workhorse. Good traction, hides small imperfections, and the least expensive finish. Suits most driveways and side yards.
- Exposed aggregate: pea gravel is exposed at the surface for texture and a warmer look. Adds roughly 15 – 25% to the finish cost and needs resealing every few years.
- Stamped or colored concrete: mimics stone or brick at a lower price than real pavers. We keep this narrow here; for full paver work see our Driveway & Pavers in Glendale page.
- Slab thickness: 4 inches for a standard passenger car drive, 5 to 6 inches where trucks, RVs, or heavy equipment will park. Thicker slab costs more in concrete and labor but prevents the cracking that comes from undersized pours.
- Reinforcement: mesh is adequate for light loads; rebar is standard for driveways and worth the small upcharge. Fiber mesh is a supplement, not a replacement for steel.
- Sealer: a penetrating sealer every 2 to 3 years slows moisture intrusion and reduces staining. A surface sealer gives a glossier look but needs more frequent reapplication.
You’ll also decide whether the driveway ties into a broader project. If it’s part of a full exterior rebuild, homeowners often pair this with Door Installation in Glendale when the garage or entry gets reworked at the same time.
What Concrete Driveways & Concrete Work Costs in Glendale, CA

Expect $4,500 to $12,000 for a concrete driveway install, $5,000 to $14,000 for a full replacement, and $250 to $700 for sealing. Line-item ranges below show where the money goes.
| Item | Typical Range |
|---|---|
| Concrete driveway installation (2-car) | $4,500 – $12,000 |
| Full driveway replacement (demo + pour) | $5,000 – $14,000 |
| Driveway sealing | $250 – $700 |
| Exposed aggregate upgrade | +15 – 25% of finish cost |
| Rebar upgrade (vs. mesh) | +5 – 10% of slab cost |
Several variables move a job between the low and high end of that band:
- Size and access: a 400-square-foot drive is not a 900-square-foot one, and a tight hillside lot with no truck access means more hand work and a higher labor share.
- Existing condition and base: if the old slab broke because of subgrade failure, excavation and base rebuild add cost before the new pour.
- Drainage and grading: hillside properties with slope need swales, drains, or retaining detail, which is a real line item on Verdugo foothills lots.
- Material grade: standard gray broom finish sits at the low end; exposed aggregate, stamping, and designer colors push toward the high end.
- Permit scope: most like-for-like driveway replacements don’t require a permit, but grading, drainage tie-ins, or new curb cuts do, and the plan review adds both time and fees.
A written estimate from us spells out slab thickness, reinforcement, base depth, finish, and haul-off. What it usually does not include: unforeseen subgrade repair discovered during demo, retaining walls, and landscape restoration, all of which we flag in writing before work starts so there are no change-order surprises.
See the difference
Before
After
Before
After
Before
AfterWhat Glendale Homes Specifically Do to This Job
Glendale’s build pattern shapes concrete work in ways a flat inland suburb doesn’t. Hillside infill and seismic retrofit of mid-century homes is the defining feature here, with steep lots in the Verdugo foothills and Chevy Chase Canyon where new foundations and soft-story upgrades must meet some of the strictest seismic and hillside grading codes in the state. On the streets off Glenoaks, a simple driveway replacement can trigger a geotechnical review if the grading scope crosses a threshold, so we check that before we quote. The city’s housing stock spans 1920s-40s Spanish Colonial and Craftsman bungalows near downtown, 1950s-60s ranch homes, and contemporary hillside customs, and the older slabs we break out often lack the base depth and drainage detail today’s code expects. Glendale’s hot, dry summers and Santa Ana winds matter here too: sun-baked slabs without a sealer chalk and crack faster, and slopes without proper drainage erode the base under a driveway within a few seasons. Our Driveway & Pavers service covers the wider exterior concrete scope, and homeowners often pair this with ADU Site Prep & Utilities in Glendale when a new driveway has to serve a detached unit. We work across Glendale, from the flat lots downtown to the hillside streets above the Rose Bowl side of town, and we cover nearby communities like Burbank and La Cañada Flintridge through our Glendale service area.
Serving Glendale, CA – Our Local Coverage Area
We serve Glendale and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Concrete Driveways & Concrete Work in Glendale

Most residential concrete driveways in Glendale take 3 to 5 working days from demo to finished pour, plus 7 days before you can drive on it. Hillside lots with grading or drainage work can stretch the schedule by a week or more. Call (844) 797-7958 to schedule a free estimate and get a specific timeline.
A like-for-like driveway replacement usually does not require a permit, but new grading, drainage ties, or curb cuts do. Hillside properties above Glenoaks and in Chevy Chase Canyon are the ones most likely to trigger a grading review. We pull permits when they’re required and pass inspection before the final walkthrough; call (844) 797-7958 and we’ll tell you whether your job needs one.
Concrete driveways in Glendale typically cost $4,500 to $12,000 for a new install, and $5,000 to $14,000 for a full replacement. Size, base condition, drainage, and finish grade are what move the number. Call (844) 797-7958 for an exact quote; estimates are free and written line-item.
No, not for the scope in the written estimate. The only adjustments we make are for conditions we couldn’t see before demo, like failed subgrade or an unexpected utility line, and those get priced and approved by you in writing before we touch them. Call (844) 797-7958 to start with a free, no-hassle estimate.
Every concrete project we complete is backed by our 730-Day Done Right Promise: if it’s not done right, we make it right for two full years from completion. That covers workmanship on the pour, finish, and joint cutting. Call (844) 797-7958 with any warranty question and a live person answers.
Ready for a Free Concrete Estimate in Glendale?
Call (844) 797-7958 to schedule a free on-site estimate for concrete driveways and concrete work in Glendale. We’ll walk the property, measure the slab, check drainage and access, and hand you a written line-item quote with thickness, reinforcement, finish, and haul-off spelled out. No pressure, no vague pricing, no surprises after the pour. Upfront pricing, live person on the call, 24/7.
Written by the team at Groundwork Construction Co.












