







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Burbank, CA: What It Costs and How Long It Takes
A chain link fence in Burbank runs $3,500 to $9,000 for most residential lots, and a standard backyard job is installed in two to four working days. The price swings on linear footage, height, gauge, gate count, and what’s buried along the fence line. If your property sits in one of Burbank’s older Magnolia Park or Rancho Equestrian blocks, add half a day for concrete removal and root work. Call (844) 797-7958 for a free on-site estimate with a written line-item quote before anything gets ordered.
How a Chain Link Fence Goes In, Stage by Stage

Fence work looks simple from the curb. It isn’t. The buried half is where a job succeeds or fails, and in Burbank’s older yards we spend as much time on what’s underground as what’s visible. Here’s the real sequence.
Stage 1: Site walk and locate (day of estimate, about 45 minutes). We measure the run, mark gate locations, and check the termite and utility clearances. Because so many Burbank lots date to the 1920s through the 1950s, we also look for old footing remnants from a previous fenceline. You decide fence height (4, 5, or 6 feet) and where the gate goes at this stage. Get the gate placement right now, not in week two.
Stage 2: Utility marking and layout (1 to 2 days). Before a post goes in, the line gets flagged. Burbank yards often carry irrigation, gas at the rear, and old drain lines, and even the flatland blocks have surprises. We string a line and stake each post position at 8 to 10 feet on center. This is where you confirm any slope transitions and where a driveway or side gate crosses the run.
Stage 3: Demo and post setting (day 1 to day 2 of install). Old fence comes out, concrete debris and root mass get cleared, then posts go in. Terminal posts, corner posts, and gate posts get set deeper in concrete than line posts because they carry the tension. Concrete needs to cure before tension goes on, so this stage ends with the fence standing but slack.
Stage 4: Framing and fabric (day 2 to day 3). Top rail, tension wire, and the mesh get pulled and tightened. This is the part that decides whether the fence looks crisp or sags two years later. We pull fabric taut at the terminal posts and check rail alignment down the whole run. Fence gates get hung at this stage so swing and latch line up before hardware is final.
Stage 5: Hardware and walkthrough (same day, about an hour). Gate latches, hinges, and any privacy slats or tension bars go on. Then we walk the run with you. You check gate swing, tension, and post plumb. This is also where the 730-Day Done Right Promise matters: if a rail sags or a gate drifts, we come back and fix it, in writing. Read about how a longer property line fits into a full Fence Installation in Burbank project if you’re fencing more than one side.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Chain Link Options You’ll Choose Between
There are real decisions to make, and each carries a trade-off worth knowing before you sign.
- Vinyl-coated vs. galvanized mesh. Galvanized is the budget pick and holds up in dry Burbank heat, but it looks industrial. Vinyl-coated (green or black) adds roughly 30 to 50 cents per linear foot and reads softer against stucco and landscaping. Most homeowners here pick black or green coated on visible sides.
- Gauge (wire thickness). 11-gauge is the standard residential fabric; 9-gauge is heavier and resists bending where kids or dogs lean on it. For a fence line along a sport court or the equestrian district, the heavier gauge earns its cost.
- Height. 4 feet clears most side-yard limits, 5 feet is the common privacy compromise, and 6 feet needs a check against lot-line rules and any HOA overlay. Taller fence means deeper posts and more concrete.
- Gates. Single swing gates in a matching frame are standard. Driveway-width double gates add a few hundred dollars in frames, hinges, and drop rods.
- Top rail and tension wire. A top rail gives a cleaner sightline and holds shape; a bottom tension wire keeps the fabric from lifting. Do both where budget allows.
- Privacy slats. If you want screening without a solid wall, woven or winged slats install into the existing mesh. They cut sightlines but trap some heat and add to the base cost.
What a Chain Link Fence Costs in Burbank, CA

Most residential chain link jobs in Burbank land between $3,500 and $9,000. That range is wide on purpose; here’s what pushes a job toward either end.
| Line item | Typical Burbank range |
|---|---|
| Standard residential run, 4 to 5 feet, galvanized | $3,500 – $6,000 |
| Extended or multi-side run with coated mesh | $6,000 – $9,000 |
| Gate framing and hardware (per gate) | $300 – $800 |
| Privacy slats (added, per linear foot) | $3 – $8 |
| Old concrete footing and debris removal | $250 – $900 |
| Extra-deep post setting on sloped or hillside lots | $500 – $1,500 |
The variables that move the number:
- Linear footage. The single biggest driver. A short side-yard run prices very differently from wrapping three sides of a corner lot.
- Existing condition. Removing an old fence, ripping out buried concrete, and clearing root mass across a legacy Burbank yard all cost labor time.
- Grade and slope. Flat Magnolia Park lots are straightforward. Hillside and foothill streets above the valley floor need stepped panels and deeper posts.
- Material grade and coating. Galvanized to heavy-gauge vinyl-coated is the spread between the low and high end.
- Gate count and scope. Extra gates, wide doubles, and slats stack onto the base.
A written estimate from us lists footage, gauge, coating, gate hardware, and removal as separate lines. What’s typically not included: relocating existing utilities or irrigation in the run, and any repair to the neighbor’s side of a shared line. Ask before you sign. Upfront pricing means the number you see is the number you pay, no change orders halfway through.
See the difference
Before
After
Before
After
Before
AfterWhat Burbank Homes Specifically Do to a Chain Link Fence
Burbank is a company town built on the soundstage economy, and that shapes how work gets scheduled here. Many residents work in entertainment, and a lot of them want the yard buttoned up fast between projects, with permit-ready, camera-friendly results. That matters for fencing because a clean, plumb run against a freshly painted stucco wall is what these yards are judged on.
The housing stock does the rest. Magnolia Park and the Rancho Equestrian district carry 1920s to 1940s Spanish Revival and Craftsman bungalows with original lath-and-plaster and the occasional unpermitted addition or converted garage. Those surface the moment a permit gets pulled, and a fence line that runs along an unpermitted structure or a converted garage turns from fence job into a scope question. Pair the screening work with ADU Site Prep & Utilities in Burbank if you’re converting a garage and fencing its yard at the same time. On the flatland blocks and post-war flats near downtown, dry summers and Santa Ana wind scrape the galvanized coating and grind the mesh along the rails, so we spec heavier gauge and tighter tension on exposed south- and west-facing runs. On the Verdugo foothill streets, fire-clearance rules mean the fence can’t sit in the brush clearance zone, and sloped lots need stepped panels with deeper post settings. We cover all of it across Burbank.
Serving Burbank, CA – Our Local Coverage Area
We serve Burbank and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chain Link Fence in Burbank

Most standard residential chain link fence jobs in Burbank take two to four working days once the site is clear. Concrete cure time between post setting and tensioning is the one step you can’t rush, so expect a one-day gap on most jobs. Larger runs, hillside lots, and heavy old-fence demo push toward the four-day end. Call (844) 797-7958 to get a firm timeline from a site walk.
Fence permitting in Burbank depends on height, setback, and lot location, and hillside and fire-clearance streets carry extra review that flatland lots don’t. We check your lot against current requirements during the estimate and tell you in writing whether a permit is needed before any post goes in. Hedging on this is how jobs get red-tagged, so we handle the check up front. Call (844) 797-7958 and we’ll walk your specific lot.
Yes. Utility-marked layout keeps posts clear of irrigation, gas, and drain lines, and we hand-dig at tight spots rather than running an auger blind through a legacy Burbank yard. That’s most of why a site walk matters before we touch a shovel. If a post position collides with a line, we move the panel rather than the line. Call (844) 797-7958 to schedule the walk-through.
Expect $3,500 to $9,000 for most residential chain link fence projects in Burbank, with the spread driven by footage, gauge, coating, gate count, and how much old demo is buried in the yard. Coated and heavy-gauge fence sits at the top; a short galvanized side-yard run sits near the bottom. Call (844) 797-7958 for an exact quote; estimates are free.
Our 730-Day Done Right Promise covers workmanship on every chain link fence we install: if it’s not done right, we make it right for two years. That covers tension, gate alignment, and post setting. Material defects run against the manufacturer’s own warranty, which we explain in writing at the estimate. Call (844) 797-7958 and we’ll put the terms in your quote.
Get a Free Chain Link Fence Estimate in Burbank
Call (844) 797-7958 and a live person answers, day or night. We’ll set a free on-site estimate, walk your property line, and hand you a written line-item quote covering footage, gauge, coating, gate hardware, and removal. Our technicians bring up to 12 years of experience to the job, arrive in uniform, and pass a background check. If you’re refreshing the exterior at the same time, ask about pairing this with our Door Installation in Burbank or a broader Fence Installation scope. No pressure, no surprises.
Written by the team at Groundwork Construction Co.












